Embroidery Explained
Definition
Embroidery builds a design out of thread, stitched into the fabric by a computer-driven machine following a digitised stitch file. The finish is raised, textured and reads as premium, and it typically outlives any printed decoration, which is why it remains the standard choice for corporate uniforms, polos, caps and outerwear.
How it works
- Digitising — the artwork is converted into a stitch file by an operator who decides stitch types, directions, densities, underlay and sequencing. This is a manual craft, not an automatic conversion, and it is the single biggest factor in final quality.
- File output — saved in a machine format such as DST or EMB.
- Hooping — the garment is clamped in a hoop with a backing stabiliser behind it to stop the fabric distorting.
- Threading — each needle is loaded with the required thread colour.
- Stitching — the machine stitches the design, changing colour automatically.
- Trimming and finishing — jump stitches are trimmed, backing is torn or cut away, and the piece is pressed.
- QC — check registration, density, thread breaks, puckering and placement.
Best used for
- Corporate uniforms and workwear — polos, shirts, jackets, vests
- Caps and headwear, where printing performs poorly
- Premium and heavyweight items: fleece, softshell, outerwear, bathrobes, towels
- Small to medium logos, typically under 100 mm wide
- Applications needing maximum durability and a high-perceived-value finish
- Bags, aprons, blankets and heavier textiles
- Any garment where a printed finish would look cheap
Not suitable for
- Large-area designs — stitch counts and cost escalate very fast
- Photographic images, gradients or subtle colour blends
- Very fine detail or small text — anything under roughly 5 mm tall will not read
- Thin, delicate, stretchy or performance fabrics without careful stabilisation
- Waterproof garments, where needle holes compromise the membrane
- Designs with large numbers of colours (most machines run 12–15 needles)
- Budget-sensitive high-volume merchandise
Compatible materials
| Material | Works | Notes |
|---|---|---|
| Pique polo / cotton | Excellent | The benchmark application |
| Fleece and softshell | Excellent | Needs a topping to stop stitches sinking |
| Structured caps | Excellent | Requires a cap frame and adjusted digitising |
| Denim and canvas | Excellent | Very stable |
| Towelling / bathrobes | Good | Water-soluble topping essential |
| Knitwear | Good | Careful stabilising to avoid distortion |
| Lightweight woven shirting | Good | Lighter backing; keep density low |
| Performance stretch | Conditional | Cut-away backing, reduced density |
| Waterproof / membrane | Not recommended | Needle perforations breach waterproofing — use a patch |
| Leather | Conditional | Perforation is permanent; test first |
| Very thin fabric | Poor | Puckering risk is high |
Colour capability
Thread colours are chosen from a fixed thread manufacturer’s shade chart. Matching is done by selecting the closest available thread to a Pantone — it is a selection, not a mix, so an exact match is not always available. Gradients and photographic blending are not achievable; blends are approximated with techniques such as thread blending, which is a specialist effect. Most machines run up to 12–15 colours in a single design.
Order quantities
- Practical minimum: 1 piece once digitising is done; 12–25 is the usual commercial minimum
- Economic sweet spot: 25–500 pieces
- Practical maximum: unlimited
Digitising is a one-off cost per design, per size. Reorders of the same logo at the same size skip it entirely — always check whether the file is already on record. Resizing a logo significantly usually requires re-digitising, which customers rarely expect and should be told up front.
Size and imprint limits
Typical hoop sizes cap designs at around 300 × 200 mm, with most corporate logos running 60–100 mm wide on the left chest. Caps are more restricted still, commonly around 110 × 55 mm on the front panel, and curvature dictates how the design is digitised. Sleeve, nape and cuff positions are smaller again.
Durability
The most durable decoration available on apparel alongside sublimation. Thread does not crack, peel or fade meaningfully and typically outlasts the garment. Failure modes are snagging, and thread wear at high-abrasion points. Industrial laundering is generally tolerated well, which is why embroidery dominates hospitality and healthcare uniforms.
Artwork requirements
| Requirement | Spec |
|---|---|
| Preferred format | Vector — AI, EPS, PDF |
| Raster fallback | 300 DPI, clean, high contrast |
| Machine file | DST or EMB if you already have one — always ask |
| Minimum text height | ~5 mm for legibility |
| Minimum line width | ~1 mm |
| Detail | Simplify. Fine detail, thin outlines and gradients must be redrawn |
| Colours | Specify Pantones; we match to the nearest thread |
| Size | State the exact finished width — digitising is size-specific |
Setup requirements
Digitising is the setup, charged once per design per size. It is skilled manual work and directly determines whether the logo looks sharp or muddy. Cheap digitising is the most common cause of a disappointing embroidery job. Hooping and machine setup add a small per-run cost.
Indicative lead time
Indicative only. Confirm every job with production before committing to a date.
| Stage | 12–50 pcs | 50–250 pcs | 250–1,000 pcs |
|---|---|---|---|
| Brief and artwork check | Same day | Same day | 1 day |
| Digitising (new logo) | 1–2 days | 1–2 days | 1–2 days |
| Stitch-out sample | 1 day | 1 day | 1–2 days |
| Customer approval | customer-dependent | customer-dependent | customer-dependent |
| Production | 1–3 days | 3–5 days | 5–10 days |
| QC and pack | Same day | 1 day | 1–2 days |
| Total after approval | 4–7 working days | 6–10 working days | 10–16 working days |
Reorders with digitising already on file drop 2–3 days from these bands.
Finish and feel
Raised, textured and tactile. Reads as premium and substantial, which is why it commands a price premium over printing on the same garment. 3D puff embroidery uses foam under satin stitching for a strongly raised effect, used heavily on caps. The reverse side of the garment will show the stitching and the backing unless a backing-cover is applied.
Common defects and how to avoid them
| Defect | Cause | Prevention |
|---|---|---|
| Puckering around the design | Wrong backing, over-tight hooping, density too high | Match backing to fabric; reduce density |
| Illegible small text | Text below minimum height | Enforce 5 mm minimum at quoting stage |
| Stitches sinking into pile | No topping on fleece or towelling | Use water-soluble topping |
| Gaps between colours | Insufficient underlay or pull compensation | Fix at digitising stage |
| Thread breaks leaving gaps | Tension, worn needle, poor thread | Preventive maintenance; inspect each piece |
| Distorted design on caps | Flat digitising used on curved panel | Digitise specifically for cap frames |
| Logo too big / off-centre | Placement not jigged | Use placement templates per garment type |
Cost drivers and break-even
Cost is driven by stitch count, not by physical size or colour count. A dense 1,000-stitch logo costs less than a sparse 15,000-stitch one. Rough guide: a standard left-chest corporate logo runs 4,000–12,000 stitches. Cost levers:
- Simplify the artwork — remove fine detail and unnecessary fills
- Reduce physical size — fewer stitches
- Swap solid fills for outlines where the design allows
- Reorder at the same size to reuse digitising
Against print: embroidery is more expensive per unit on small logos at volume but is expected on uniforms, where printed logos read as low quality.
Compared with alternatives
vs Screen printing — embroidery is more durable and more premium; screen printing is far cheaper for large designs and handles flat colour graphics better.
vs DTF — DTF reproduces photographic and multi-colour artwork that embroidery cannot, at lower cost on large designs. Embroidery wins on uniforms, caps and outerwear where feel and longevity matter.
vs Woven or embroidered patches — a patch avoids stitching through the garment, which matters on waterproof or delicate items, and can carry finer detail. Patches are the standard workaround for membrane fabrics.
In Australia and New Zealand
Across Australia and New Zealand a large share of embroidery work lands on workwear, and certified high-visibility garments are governed by AS/NZS 4602.1, with retroreflective tape covered by AS/NZS 1906.4. Stitching through tape, or covering enough of the fluorescent background to fall below the area the standard requires, can take the garment out of compliance. We confirm logo position and size on hi-vis against the garment specification before digitising begins.
FAQs
What is digitising and why am I being charged for it?
Digitising converts your logo into a stitch file — a skilled manual process that decides how every stitch is laid down. It is a one-off cost per design per size, and it is what separates a crisp logo from a muddy one.
Will I pay digitising again on my next order?
No, provided the logo and the size are unchanged. Significantly resizing it usually requires re-digitising.
How small can text be embroidered?
About 5 mm tall as an absolute floor. Below that, thread thickness means the letters fill in and become unreadable.
Can you embroider a photograph?
No. Embroidery uses solid thread colours and cannot reproduce gradients or photographic detail. For photographic artwork, use DTF or sublimation.
Why is my embroidery quote based on stitch count?
Machine time is the cost. A design with more stitches takes longer regardless of how large or colourful it looks.
Can you embroider caps?
Yes, using a cap frame. Caps need to be digitised specifically for the curve — using a flat design on a cap is a common cause of distortion.
Can you match my exact brand colour in thread?
We match to the nearest available thread on the manufacturer’s shade chart. Thread is selected, not mixed, so an exact Pantone match is not always possible — we will show you the closest option.
Can you embroider a waterproof jacket?
Not recommended, because the needle perforates the membrane. The standard solution is an embroidered patch attached without breaching the waterproof layer.
What logo size should be digitised for a standard Australian corporate polo?
Left chest logos here are normally specified in millimetres, commonly around 70 to 90 mm wide. Because digitising is size-specific, confirm the finished width before the stitch file is created; a later resize of any significance means re-digitising.
Can you embroider certified hi-vis workwear without affecting compliance?
Yes, provided the logo is positioned and sized against AS/NZS 4602.1 and AS/NZS 1906.4. Stitching must not cross retroreflective tape, and enough fluorescent background has to remain uncovered. Send the garment specification through before digitising so the design is built to the right size first time.
Last reviewed: 13/09/2026 · Owner: Lenny Ferreira · Confidence: industry standard (awaiting verified Printshop4me production data) · Version: 1.0
